Background
New drought tolerant varieties of key crops are needed to ensure food security. To evaluate the water-use efficiency of a drought tolerant variety, the USDA-ARS (Flagstaff, AZ, USA) used the ICT International Sap Flow Sensor (SFS) in conjunction with weighing lysimeters. This combination measured plant water use and pot mass changes respectively over 12 days in 8 individually potted plants.
Methods
Eight individual potted maize were prepared and placed in a greenhouse; 4 non-drought tolerant control (nDR) and 4 drought tolerant (DR). Each plant was instrumented with a Sap Flow Sensor (SFS) with 12 mm needles, fully contained within the maize stem, and placed on separate weighing lysimeters.
The individual plants were placed in a potting medium covered with coarse sand and plastic film to minimise surface evaporation. This ensures that evaporation changes in pot mass could be attributed primarily to plant water use.
The resulting data was integrated at hourly intervals to describe the hourly dynamics of sap flow (cm/h) and pot mass change (g). Separate time-series were analysed for the DR and nDR maize genotypes.
About the Heat Ratio Method and SFMx Sap Flow Sensor
The Heat Ratio Method of Burgess et al. (2001) implemented in the ICT International Sap Flow instruments has been used in over 250 peer-reviewed publications. As the methodology has been recognised for the versatility that it brings to measuring plant water relations, particularly in drought tolerance research, the need for different needle (thermistor positions) has been identified. This has led to the development of 12 mm and 22.5
mm needles alongside the 35 mm needle.
The Heater Needle is designed to provide the same joules per millimetre of heat, whilst the thermistor needles have two high-sensitivity thermistors embedded in each needle. In the case of the 12 mm needle, these thermistors are positioned 2.5 mm and 9.5 mm from the needle tip to sample temperature within the active xylem.
These needles can be specified with either with an SFMx stand-alone logger (with multiple communications options) or as SDI-12 compatible sensors within existing datalogging and monitoring networks. Sap flow needle options available include 12 mm, 22.5 mm, and 35 mm.
The diurnal change in mass of potted maize corresponded well with the fluctuations of sap flow, confirming that the needle-type sap flow sensor captured whole-plant water use with high fidelity under greenhouse conditions (Figure 1). The nDR maize (Figure 1A) consistently shows lower sap flows and smaller diurnal mass changes than the DR maize (Figure 1B), indicating reduced transpiration despite being grown under the same conditions.
This pattern is consistent with previous findings, that drought-tolerant maize lines often maintain higher transpiration and sap flow under mild stress or controlled conditions, while more susceptible lines conserve water via reduced leaf area expansion and stomatal conductance, but at the cost of growth and yield (Klimešová et al., 2017).
In this experimental setup, the diurnal loss of pot mass can be interpreted as plant water use, as soil surface evaporation was minimised by the sand and plastic cover. The strong linear relationship between sap flow and gravimetric mass loss for both genotypes (DR, R2 = 0.9138; nDR, R2 = 0.9157; Figure 2A, B) indicates that lysimeter mass change is predominantly driven by xylem water transport.
Consequently, the 12 mm needle sap flow sensor provides a reliable proxy for whole-plant transpiration under these conditions. This agreement between sap flow and lysimeter measurements is consistent with previous validation studies in maize, where sap flow sensors have reproduced gravimetric transpiration with high accuracy (Capurro et al., 2024; Wang et al., 2017). The similar level of correspondence observed here supports the reliability of the 12 mm needle geometry in herbaceous stems and confirms that the thermal signal is effectively
constrained to the conducting xylem.
Results show a close match between sap flow measured with the 12 mm needles and the independent changes in pot mass for both maize genotypes. This gives clear confidence that the new sensor can quantify plant water use in small-diameter stems. Capturing the daily pattern of transpiration and clearly separating the behaviour of DR and nDR plants, the 12 mm sensor offers a practical alternative to large weighing systems and can be further implemented for screening drought-tolerance traits, testing crop models and designing irrigation strategies in maize and other herbaceous species.
Burgess, S. S. O., Adams, M. A., Turner, N. C., Beverly, C. R., Ong, C. K., Khan, A. A. H., & Bleby, T. M. (2001). An improved heat pulse method to measure low and reverse rates of sap flow in woody plants. Tree Physiology, 21(9), 589–598. https://doi.org/10.1093/treephys/21.9.589
Capurro, M. C., Ham, J. M., Kluitenberg, G. J., Comas, L., & Andales, A. A. (2024). A novel sap flow system to measure maize transpiration using a heat pulse method. Agricultural Water Management, 301, 108963. https://doi.org/10.1016/j.agwat.2024.108963
Klimešová, J., Holková, L., & Středa, T. (2017). The Expression of Dehydrin Genes and the Intensity of Transpiration in Drought-stressed Maize Plants. Cereal Research Communications, 45(3), 355–368. https://doi.org/10.1556/0806.45.2017.017
Wang, Y., Zhang, X., Xiao, X., Heitman, J., Horton, R., & Ren, T. (2017). An Empirical Calibration for Heat-Balance Sap-Flow Sensors in Maize. Agronomy Journal, 109(3), 1122–1128. https://doi.org/10.2134/agronj2016.10.0611
ICT International Pty Ltd thanks Joseph Michaud and Louis Comas (USDA‑ARS, Flagstaff, AZ, USA) for their support with the experimental setup, validation of the 12 mm sensor and provision of data used in this case study.
Authors:
Riccardo Mazzoleni, PhD (Application Scientist)
Beng Umali, PhD (Lead Application Scientist)
Ed Lefly, PhD (R&D Head)
Rahinul Hoque (Electronics Engineer)