The SNiP-SOA is a 'Sensor Node Integrated Package' for LoRaWAN or CAT-M1 communication of real-time soil oxygen measurement for continuous soil monitoring.
The base SNiP-SOA integrates 1x S-NODE and 1x SO-411 Soil Oxygen Sensors from Apogee’s SO-400 Series to a site’s unique network, communication and power requirements. The S-NODE can support an added 1x SO-411 Soil Oxygen Sensors to monitor soil moisture at multiple depths.
The SO-411 Soil Oxygen Sensor has a standard response time of 60 seconds and is designed for for the measurement of soil oxygen content (%) of soils with SDI-12 Output.
Additional parameters can be added to SNiP-SOA, without requiring loggers to match each distinct sensor, substantially reducing the cost of getting a fuller picture on the application.
The protective membrane in front of the oxygen sensor can be heated to prevent water from condensing on the membrane and blocking the diffusion path. The heater is typically used when sensors are deployed in soil or compost where relative humidity is close to 100%.
Housed in a polypropylene body and electronics are fully potted, ideal for long-term deployment in porous media, including acidic environments (mine tailings). Two head options are available: a diffusion head that creates a small air pocket for measurement in porous media and a flow-through head with two adapters for tubing that allows measurement of gas flowing in lines.
Internal Temperature Sensor
All oxygen sensors have an internal thermistor (type-K thermocouple is available upon request) that allows for temperature monitoring and correction of signal for temperature effects.
Voltage output is linearly proportional to absolute amount of oxygen. Calibration is accomplished by measuring the voltage under ambient conditions (atmosphere is 20.95% O2) and deriving a linear calibration factor (slope). A zero offset can be measured with N2 gas (recommended for measurements below 10% O2).
Applications include: measurement of O2 in laboratory experiments, monitoring gaseous O2 in indoor environments for climate control, monitoring of O2 levels in compost piles and mine tailings, monitoring redox potential in soils, and determination of respiration rates through measurement of O2 consumption in sealed chambers or measurement of O2 gradients in soil/porous media.
The S-NODE (for Environmental Monitoring) has been designed to support the broad suite of SDI-12 based environmental sensors. The S-NODE can support sensors with higher power requirements; a solar panel can charge either the internal lithium-ion battery or both the node and sensor can be powered by an external 12V system (e.g. battery or mains source).
A decoder suitable for TTN will be provided based upon sensor configuration.
The SO-411 Soil Oxygen Sensor has a standard response time of 60 seconds and is designed for use in soil applications, for the measurement of soil oxygen content (%) of soils. It has SDI-12 Output and comes with a thermistor temperature sensor to correct for temperature changes and a resistive heater to raise the temperature of the membrane approximately two degrees above ambient temperature to keep condensation from occurring on the Teflon membrane and blocking the diffusion path of the sensor. Typical applications include measurement of O2 in laboratory experiments, monitoring gaseous O2 in indoor environments for climate control, monitoring of O2 levels in compost piles and mine sailings, monitoring redox potential in soils, and determination of respiration rates through measurement of O2 consumption in sealed chambers or measurement of O2 gradients in soil/porous media.
|Input Voltage Requirement||5.5 to 24 V DC|
|Current Drain||0.6 mA (quiescent); 1.3 mA (active)|
|Measurement Range||0 to 100 % O₂|
|Measurement Repeatability||Less than 0.1 % of mV output at 20.95 % O₂|
|Non-linearity||Less than 1 %|
|Long-term Drift (Non-stability)||1 mV per year|
|Oxygen Consumption Rate||2.2 µmol O₂ per day at 20.95 % O₂ and 23 C|
|Response Time||60 s|
|Operating Environment||-20 to 60 C, 0 to 100 % relative humidity (non-condensing); 60 to 140 kPa|
|Input Voltage Requirement||12 V DC continuous (for heater), 2.5 V DC excitation (for thermistor)|
|Heater Current Drain||6.2 mA (74 mW power requirement when powered with 12 V DC source)|
|Thermistor Current Drain||0.1 mA DC at 70 C (maximum, assuming input excitation of 2.5 V DC)|
|Dimensions||32 mm diameter, 68 mm length|
|Mass||175 g (with 5 m of lead wire)|
|Warranty||4 years against defects in materials and workmanship|